www.advantech.com/products Online Download Features AMAX-1220 AMAX-1240 Specifications Pulse-Type Motion Control ƒ ƒ Motor Driver Support Pulse-type servo ƒ ƒ Number of Axes AMAX-1220: 2 AMAX-1240: 4 ƒ ƒ Interpolation Linear and circular ƒ ƒ Max. Output Speed 6.5 Mpps ƒ ƒ Step Count Range ±134, 217, 728 ƒ ƒ Pulse Output Type OUT/DIR, CW/CCW, A/B phase ƒ ƒ Position Counter ±134, 217, 728 ƒ ƒ Home Modes 13 ƒ ƒ Velocity Profiles T-Curve, S-Curve ƒ ƒ Local I/O Machine Interfaces: EL+/-, ORG and SD (Slow Down) for Each Axis Servo Driver Interfaces: ALM, RDY, SVON, INP, Break for Each Axis Position Compare I/O: LTC, CMP for Each Axis(Only available for AMAX-1240-AE) Simultaneous Move Within Multiple Modules: CSTA/CSTP (Simultaneously Start/Stop) for each model General Purpose I/O: AMAX-1220 supports 8xDI and 8xDO Encoder Interface ƒ ƒ Input Type A/B phase, CW/CCW ƒ ƒ Counts per Enc. Cycle x1, x2, x4 (AB phase only) ƒ ƒ Input Range Low: 0 ~ 0.5V High: 3.5 ~ 7V ƒ ƒ Isolation Protection 2,500 VRMS ƒ ƒ Max. Input Frequency 2 MHz @ 5 V General ƒ ƒ Bus Type AMONet RS-485 ƒ ƒ Certification CE, FCC Class A ƒ ƒ Connectors RJ-45 x 2 are for communication port DB-26 connector by transfer cable to servo drives. Other are screw terminal type connectors ƒ ƒ Dimensions (L x W x H) 141 x 108 x 60 mm (5.6" x 4.3" x 2.4") ƒ ƒ System Power 2 W @ 24 V typical Consumption Output Channel Power Consumption 120W typical, 240W max. Input Channel Power Consumption AMAX-1220: 8 W @ 24 V external power (max.) AMAX-1240: 10 W @ 24 V external power (max.) ƒ ƒ System Power Input 24 VDC within 200 mV ripple ƒ ƒ Humidity 5 ~ 95% RH, non-condensing (IEC 60068-2-3) ƒ ƒ Operating Temperature 0 ~ 60°C (32 ~ 140°F) Ordering Information ƒ ƒ AMAX-1220-AE Economic 2-axis AMONet Motion Control Module ƒ ƒ AMAX-1240-AE Advanced 4-axis AMONet Motion Control Module Accessories ƒ ƒ PCL-10153PA5-2E 50-pin Cable to Panasonic A4/A5 Servo, 2 m ƒ ƒ PCL-10153PA5LS-2E 50-pin Cable to Panasonic MINAS A Servo, 2 m ƒ ƒ PCL-10153YS5-2E 50-pin Cable to Yaskawa Sigma V/7 Servo, 2 m ƒ ƒ PCL-10153MJ3-2E 50-pin Cable to Mitsubishi J3/J4 Servo, 2 m ƒ ƒ PCL-10153DA2-2E 50-pin Cable to Delta A2 Servo, 2 m Introduction AMAX-1220 and AMAX-1240 have compact open frame designs for horizontal placement and an interface connector mounted on the board. With a transfer cable to servo drive, both models can conveniently connect to Mitsubishi J3, Yaskwa Sigma V and Panasonic A4/A5. The AMAX-1220 is an economic 2-axis AMONet slave module which supports motion functionality in point-to-point (PTP), linear & circular interpolation, simultaneously start/ stop among multiple slave modules, and brake signal to servo for emergence consideration. The AMAX-1240 is an advanced 4-axis AMONet slave module which not only supports AMAX-1220 motion functionality, but also supports advanced features in position compare and triggering function. Both linear interval and table setups are supported. ƒ ƒ End limit logic is switchable (high or low active) ƒ ƒ BoardID is switchable ƒ ƒ Easily visible LED indicators on board to do diagnosis ƒ ƒ Direct wire to servo drive to save terminal board space while installation ƒ ƒ Max. 6.5 MHz, 4-axis pulse output ƒ ƒ 28 bits counter for incremental encoder ƒ ƒ Horizontal installation for for servo or stepping motor driver ƒ ƒ Suitable for DIN-rail mounting Open Frame-Type 2/4-Axis AMONet Motion Slave Modules AMAX-1220 AMAX-1240 RoHS COMPLIANT 2002/95/EC Power & Energy Automation 8 5 4 4 10 Panel PCs 9 iDoor Technology Modules 8 Industrial monitors 7 Industrial IoT Gateways 6 Control Cabinet PCs High-Performance Control Panels Industrial Operator Panels 3 2 IntelligentMotionControl andMachineVision 1 WebAccess+ Solution 11 Control IPCs 12 Remote DA&C Systems 13 Wireless IoT Sensing Devices 14 15 RS-485 I/O Modules 16 Thin-Client Terminals Industrial Ethernet Solutions 17 IP Gateway and Serial Device Servers iNetworking 18 19 Ethernet I/O Modules Chapter 2 Table of Contents Table of Contents